1970 F85 W31
#81
This can be a VERY expensive hobby and I consider it a hobby not a money making deal unless like stated earlier "the only way to make money in this is; work on other peoples cars." The cars I am building are "drivers" non originals, modernized for convenience , safety and SPEED. I never plan on building or having one built that cannot be taking out and getting caught in the rain, wife can drive it without coming home with a stone chip and me freaking out over it. Besides my German Shepherd loves to ride in the back seat! The cars may not be worth what I got in them, but at least they hold their value and I am having fun going on cruises-the 67 went on the Hot Rod Power Tour last year broke the motor in and had a blast. Have some dings to prove it!64post.jpgDSCN2133.jpgDSCN1932.jpg
#83
It's a built 30 over 455-500 HP on 93 octane, Torker, Edelbrock heads, Harlin Sharp Roller Rockers, Coyles roller chain, Comp Cams Extreme Energy274-pretty basic Olds recipe with some detail. M-21 4-speed, Ram Power Grip clutch, 8.5 GM 10bolt-3:55 gears, Holley electric fuel pump with .8an braided stainless steel fuel line with all an fittings, A Dean Oliver race prepped 800 CFM Q-jet, aluminum radiator, 72 Cutlass P/S pump. new Painless engine wiring harness, RobMac 1/2 inch fuel pickup, 3 inch Mandrell bent exhaust with Spin Tech mufflers, Cragar 15x10 L-60x15 Diamondback redlines in the rear Cragar 15x8 235x15 Diamondback redlines in the front, solid core U-joints, completely restored suspension system the front end has new 1 inch drop springs with an all new 72 Cutlass disc brakes. Getting ready to put in a new interior, re-seal the windshield and rear window-last year on Power Tour I drove in some really heavy thunder showers and had probably 1/4 inch of rain in the floor boards! Thank goodness for the wet/dry vacs at the carwashes or at least thats what I used them for! Next up is Vintage A/C and going to have the Muncie rebuilt have them install a new steel mid plate, a new 2:52 M-20 first gear. The trans is the weakest link. If I put slicks on her and she hooked, I fear I would bust the trans. I also need to build a torque strap ASAP driver side motors are breaking lose.. Thanks for your interest.DSCN1723.jpg
#84
I love it....what is the torque number? A good buddy of mine used to drag race occasionally his 55 Chevy 210 Delray 2 door sedan, with a built 406 SBC. That engine had 475 HP with approx. 500 lbs/ft of torque. He ran a Super T10 with a Dana 60 with 4:10 gears. Car ran 12.10 at 113 MPH in the 1/4 dumping the clutch at 4500 RPMs. It was an 11 second car if he would have dumped the clutch at 5000 RPMs. I have a 1980 Malibu 2 door sport coupe with a 1970 LS6 454 that runs 11:70's @ 113.78 MPH. It has a TH350 with a 3600 stall, a 9" Lincoln Versailles diff with 3:89 gears, a Detroit locker and Strange axles. I run 15 X 28 X 9 inch slicks on 7 inch wide rims (not much wheel well space with the 1978 Lincoln Versailles diff).
Sounds like you have yourself a whole lot of fun there! Enjoy and keep us posted with any track times.
Cheers,
Sounds like you have yourself a whole lot of fun there! Enjoy and keep us posted with any track times.
Cheers,
#85
This can be a VERY expensive hobby and I consider it a hobby not a money making deal unless like stated earlier "the only way to make money in this is; work on other peoples cars." The cars I am building are "drivers" non originals, modernized for convenience , safety and SPEED. I never plan on building or having one built that cannot be taking out and getting caught in the rain, wife can drive it without coming home with a stone chip and me freaking out over it. Besides my German Shepherd loves to ride in the back seat! The cars may not be worth what I got in them, but at least they hold their value and I am having fun going on cruises-the 67 went on the Hot Rod Power Tour last year broke the motor in and had a blast. Have some dings to prove it!
#86
You might consider a Borg Warner Super T-10 tranny as they are a tad bit stronger than the Muncie trans and they have a wide variety of ratios availble and they (usually) are less money used....Just a thought behind that torque monster
#88
I have brought home most of the boxes of parts now, an the side glass, interior stuff, just the front seat is in the car. It has another steering wheel column in it from a 1972 Cutlass, just to move it around easily, the original is home now with the sport four spoke cushion grip steering wheel. I'm going to take pics of everything and then start finding a place to put the stuff. I can't bring the car home until I get this stuff organized where I want it. As well this last week was spent running a 60 amp wire underground to my garage, adding a new 100 amp sub-panel in the house to feed the garage. It was under wired for the new electric garage heater that I installed, so now I will have a properly heated work space. I have the everything but the rolling chassis/body (with doors, and trunk still attached) at home now. The car came with a 72 Cutlass frame/chassis to eventually sit the body on while a restore the original frame. Work, work, work.... ;-)
In the meantime here's a picture of my 80 Malibu with the LS6 at a local outdoor Sunday night cruise. I know, it's not an Olds.....
In the meantime here's a picture of my 80 Malibu with the LS6 at a local outdoor Sunday night cruise. I know, it's not an Olds.....
#89
Trades???
Last edited by mono-plane; October 25th, 2009 at 04:43 PM. Reason: Added more info.
#90
Thanks Monoplane. When I put the motor on the dyno to break in the cam, all I had at the time-to impatient I guess-was an Edelbrock 600cfm carb and the resuts on the sheet showed it. Anyway on that breakin period the the motor pulled 530 lbs of torque at 2,500 rpm! Only 447hp. Now the engine is tuned, the HEI has been curved and with a Dean Oliver race prepped Q-jet the motor has be very close to my initial goal 500hp. I am going to the speed shop maybe later this week and get a few pulls on the chassis dyno see what happens.
#91
My dyno sheet says she produced 502 LBS. of Torque right off idle at 3,000 RPM 447HP. Now keep in mind I was to anxious and could not wait to fire the motor and only had a measly 600CFM Edelbrock carb on the beast at the time-which starved the motor. I am going to the chassis dyno within 30 days. The motor is now well tuned with a Dean Oliver race prepped 800CFM Q-jet. See what happens, thanks for your interest...455incar2.jpg455incar.jpg
#92
Thanks JoesW31, will do. Just got the car home yesterday afternoon, so took some pics and will post a Photo Bucket link. :-)
#93
My dyno sheet says she produced 502 LBS. of Torque right off idle at 3,000 RPM 447HP. Now keep in mind I was to anxious and could not wait to fire the motor and only had a measly 600CFM Edelbrock carb on the beast at the time-which starved the motor. I am going to the chassis dyno within 30 days. The motor is now well tuned with a Dean Oliver race prepped 800CFM Q-jet. See what happens, thanks for your interest...
Last edited by mono-plane; November 6th, 2009 at 10:39 PM.
#94
OK everybody, here's some of the initial pics of my 1970 F85 W31. I have tons more pictures to take of the rest of the parts, including the interior, rebuilt motor, Super T10, etc. The rust is along the rear quarter lips, some along the base of the windshield, but not bad and some bad pitting along the metal panel along the bottom of the rear window. I have a non-tinted car with a tinted driver's door glass, the rest is original. I will need tom buy a windshield too. It has the antenna built in which I like. I also need an original radio as per my build sheet. Your thoughts and comments are appreciated.
http://s597.photobucket.com/albums/t...1%204%20Speed/
Cheers,
http://s597.photobucket.com/albums/t...1%204%20Speed/
Cheers,
#95
I will post the results ; but from all the other "OLDS recipes" 500 HP I may be pushing it on Fantasy Island. It didn't know at the time I could push the compression to 11.1 with aluminunm heads on 93 pump. The motor comp. is a true 10.25 with all the other goodies etc. That could be the difference. But what do I know I keep throwing money at it and hope it grows
#97
Hi Mono-plane. The Canadian docs that Diego posted are mine. I just posted on the newbie forum. There are a couple of pics of the car (original paint). My docs show Twilight Blue with Astro Blue stripes, and that's exactly what it is.
Cheers
Dean
Cheers
Dean
#100
#103
A friend of mine also has a W31, Astro Blue with Black stripes. Our cars have never been side-by-side, but the color looks pretty close to my stripes, so I assumed they were Astro Blue. What color do you figure they are? I know the pics aren't very good, and the paint is in poor condition.
#104
The documentation from GM of Canada says the car is Twilight Blue with Astro Blue stripes. The correct color for the blue stripes are not Astro Blue - that's what I'm saying...GM of Canada's use of the adjective "Astro Blue" for the stripe color is not correct.
#107
So the painters back in the day and since, go by some formula for all colors, whether main body colors or accent colors for the stripes. As long as you have this info, you can restore your car properly assuming that modern paints can be mixed to match the exact color? Diego, you posted the above attachment earlier in this discussion, was there a mixing formula as well? Thanks
#109
Diego, did you send me a private message? I have a post from you that's not on this thread? In answer to your comments (maybe private at this point?), it would seem very strange to keep the info quiet at this point. What purpose would it serve, unless someone is trying to profit from the info?
#110
I had a response that I wasn't sure if I could post it because a friend had asked me to keep a file on the DL, but it wasn't this one, so I edited my post and posted the item - that's where the confusion comes from.
#112
Chilly, your car looks great! Nice to see more "post strike" W-31 cars! I have noticed that cars on the east coast compared to the west coast had "body stripes" that did not match the interior color of the car. I think that is awsome! It was recommended that the "body stripe" match the interior.
#113
I have a buddy with a 1968 Chevelle 12 bolt diff but what is different about the trailing arms? Would one need both upper and lowers?
#114
Hey, I have access to a 1968 Chevelle 12 bolt, but what's different about the upper and lower trailing arms, that one would need to change them.
Barry
#115
monoplane- the rear in your car appears to be a "P" type rear. Post the codes from the axle tube, and lets see if we can find it.
Your original rear would be "TO" code olds 12 bolt 3.91 ratio. 1970 olds had a stand alone rear in the sense it had a roller bearing axle shaft. The rears are not difficult to find and now would be a great time to purchase any rare parts you are missing without digging a hole in your pocket.
Your original rear would be "TO" code olds 12 bolt 3.91 ratio. 1970 olds had a stand alone rear in the sense it had a roller bearing axle shaft. The rears are not difficult to find and now would be a great time to purchase any rare parts you are missing without digging a hole in your pocket.
Man I scraped, and wire brushed that diff to clean it up, but couldn't find any codes. I looked on the front passenger side tube, nothing. I did get approx. a half a pound of dirt, oil and grease though. ;-) My car was originally an M21. I read somewhere back in a January 1986 issue of Popular & Performance Car Review mag, which ran an article on Olds W machines. The article stated that the W31 with an M21 got 4:33 gears and the M20 cars came with 3:90 gears. Anybody out there with original cars, that have these set-ups in them from new?
Does anybody have an original diff for my W31 that they want to sell? As well as the boxed trialing arms?
Barry
#116
contact 507olds,he builds them.
he probably has the sway bar,and control arms,and the frame braces as well.
when you remove that rear,check your frame real good on the top part of the pass side spring perch.
if that was a 4 speed car,and raced,and they took those frame braces off,you could have some stress cracking in the frame up there.
ive had 2 4 speed W cars ive parted out with cracks in the frame there.
he probably has the sway bar,and control arms,and the frame braces as well.
when you remove that rear,check your frame real good on the top part of the pass side spring perch.
if that was a 4 speed car,and raced,and they took those frame braces off,you could have some stress cracking in the frame up there.
ive had 2 4 speed W cars ive parted out with cracks in the frame there.
#118
This guy here in Detroit has several complete "O" rear axles for sale. All are 2.56 open rear ends. He wants $200 each. You could easily have it rebuilt with another gear ratio and a posi: http://detroit.craigslist.org/wyn/pts/1447241915.html
Drive Train Specialists in Warren, Michigan sell posi and gearsets for Oldsmobile axles. They could rebuild any unit you to have to whatever specs you want. I have dealt with these guys in the past: they are very reliable and professional. http://www.drivetrainspecialists.com/about-us.html
On a related stripe note, my parents had a 1971 442 W30 4-speed that they bought used in the fall of 1971. It was a silver car with a black vinyl top, black interior and white stripes. It was a Michigan car. That is one car my dad wishes he had kept...
Drive Train Specialists in Warren, Michigan sell posi and gearsets for Oldsmobile axles. They could rebuild any unit you to have to whatever specs you want. I have dealt with these guys in the past: they are very reliable and professional. http://www.drivetrainspecialists.com/about-us.html
On a related stripe note, my parents had a 1971 442 W30 4-speed that they bought used in the fall of 1971. It was a silver car with a black vinyl top, black interior and white stripes. It was a Michigan car. That is one car my dad wishes he had kept...
Last edited by Kaline; November 15th, 2009 at 05:22 AM. Reason: Additional Information